FOAM Pressure Absorbing Material!

  • Schneumer
    21st Aug 2013 Member 0 Permalink

    i think me desc. seems a bit more realistic....but then again does rl foam absorb pressure? probably not....but screw realism mine just seems more foamy..... its a combination of sld and ttan if made her way....but when my way......it would be much more.....easy to destroy so surround it with frme........vote for my more realistic idea, or vote uc17's more better then realistic idea, the choice is your's! actually i have more to add. mine's rate of tmp increase is a per minute one. if it was 50 pressure, it would gain 50 tmp per minute. 265 pressure = 256 tmp per minute. The only problem is thdr and dmg, which sometimes produce pressure way over the max, but it only lasts a second. would the foam still register this? or would it stop for a moment and whatever above 256 is considered 0. Then it would be incredibly op vs bombs like this.....i know! Any number above 256 would still just register at 256........but in bombs foam would only work if it was a liquid.....basically my foam is a nerfed version, and it wouldnt work vs bombs because of the immense heat.  Also, once the foam dissappears, It'd release max pressure in the form of a pressure shockwave. (P.S. I know you all will vote for uc17's cuz its better, although mine is a bit more realistic, but you guys don't care about realism. XD)

    Edited once by Schneumer. Last: 21st Aug 2013
  • 4722202468
    22nd Aug 2013 Member 3 Permalink

    I made foam, then played around with it for a bit, and found it pretty useless. VIBR + TTAN do almost exactly the same thing.

  • NF
    22nd Aug 2013 Member 0 Permalink

    It can be put into the special category, sounds legit.

  • Schneumer
    22nd Aug 2013 Member 0 Permalink

    @4722202468!

     I made foam, then played around with it for a bit, and found it pretty useless. VIBR + TTAN do almost exactly the same thing. at least foam doesnt explode. :I hmmm.....

  • 4722202468
    22nd Aug 2013 Member 0 Permalink

    Schneumer:

    @4722202468!

     I made foam, then played around with it for a bit, and found it pretty useless. VIBR + TTAN do almost exactly the same thing. at least foam doesnt explode. :I hmmm.....

     If you do it right, VIBR doesn't explode either

  • greymatter
    22nd Aug 2013 Member 1 Permalink
    Not a bad suggestion. But all it's listed uses have clear alternatives.

    Foam can be used as an alternitive pressure detector.--Use GOO,DTEC(GOO) and a NOT gate.
    Foam can be used in walls or bunkers to absorb high pressures.--TTAN,or VIBR. Or a bit of both.
    Foam can protect any electronic equipment from pressure.--But so can TTAN.


    So might wanna step the uses up.
  • NF
    22nd Aug 2013 Member 0 Permalink

    @greymatter (View Post)

     Good Job! that would be nice also you gave me an idea. EDIT: This really needed a clear approach.

    Edited once by NUCLEAR_FOX. Last: 22nd Aug 2013
  • UC17
    3rd Oct 2013 Member 0 Permalink

    Thanks for the support, and adding water to lower the pressure woudl also be good to add to it as well.

  • lefouduroi
    3rd Oct 2013 Member 0 Permalink

    WHAT IF... FOAM could be created with the mix of SOAP and WATR? Just a thought...

  • Schneumer
    3rd Oct 2013 Member 0 Permalink

    @lefouduroi (View Post)

     and a bit of pressure, like 3. :)