Elements:Force

From The Powder Toy
Revision as of 20:09, 8 September 2014 by 12Me21 (talk | contribs) (DMG Damage)
Jump to: navigation, search
Language: English  • 한국어 • русский

Introduced in version 74.0, the Force materials are used to affect different types of matter with force. The original name of the menu was Force, but it changed into Force Creating a bit later. However, in 84.0, the name was once again renamed back to Force.

PIPE Pipe

Description: PIPE, moves particles around. Once the BRCK generates, erase some for the exit. Then the PIPE generates and is useable.

After spawning, a layer of BRCK appears around the PIPE. To set the direction of the PIPE, erase the BRCK around the end you want the particles to come out of. A series of lines will then appear showing the direction of flow, working from the end to the beginning. After the full pipe is calculated, you can remove the BRCK and replace the sides with another element.

Read the tutorial for more information (and pictures) Tutorial on how to use PIPE

ACEL Accelerator

Description: Accelerator, speeds up nearby elements.

Accelerates any non-solid particles. The LIFE determines how much the particle will be accelerated.

DCEL Decelerator

Description: Decelerator, slows down nearby elements.

Opposite of ACEL; decelerates non-solid particles. The LIFE changes how much they will be decelerated.

FRAY Force Emitter

Description: Force emitter. Pushes or pulls objects based on its temperature. Use like ARAY.

When powered, it will push elements away from the opposite side. The higher its TEMP, the more it will push them.

RPEL Repeller

Description: Repels or attracts particles based on its temperature.

Pushes or pulls particles depending on the temperature. If the temp is below 0, it will pull, and if it is above 0, it will push. Unlike FRAY, it does not need electricity to work. It affects particles within a square box of size 20 pixels centered on the RPEL particle.

DMG Damage

Description: Generates damaging pressure and breaks any elements it hits.

Generates a large force of pressure on contact with any surface except DMND. Also takes on a sparkling texture like BOMB and DEST when on fancy display.

PSTN Piston

Colour: Gray

Description: "Piston, extends and pushes particles."

Piston. When sparked using PSCN, it starts extending based on where the PSCN is. Put a 1 pixel gap between the PSTN and the PSCN for better control. It cannot extend diagonally. When it continues to extend and hits a element, it will push it.

PSTN stops extending when it hits a wall, or once it is pushing too many particles for it to handle. By default it can only push 31, but you can set the .tmp allow it to push more / less.

You can make PSTN retract with NSCN (or actually, any conductor that isn't PSCN). It will pull back the stack of elements it has in front of it when you do this. If there are too many elements in front of it, it will just pull as many as it can carry (set by .tmp).

CTYPE: if set, will make PSTN stop when it hits this element, like it would to walls.
TMP: How many pixels it can push or pull at once. if not set, defaults to 31.
TMP2: Max extension length. If not set, defaults to 255.


FRME Frame

Colour: Gray

Description: "Frame, can be used with pistons to push many particles."

FRME makes PSTN much more useful. With it, you can use just one piston to push whole blocks of elements. To start, draw a one pixel thick line of FRME in front of the piston. This can be up to 15 pixels wide in either direction. Now, when you push the PSTN, the entire line of FRME and everything in front of it will be pushed. When you retract the PSTN, it will all come back too.

If any single FRME can't move, the entire PSTN won't be able to move. Also, for retracting, any particle caught under the FRME will prevent the entire thing from retracting. Make sure to keep the path behind the frame clear.

There are several things you can't do with FRME. Any FRME stacked above the first layer (line) won't be counted as part of it, so you can't have it push or pull any oddly shaped FRME. Also don't attach multiple pistons to the FRME and try to retract, as they will block each other. There used to be many glitches for many versions causing behavior different than described here, often the FRME would break or PSTN wouldn't extend properly. These have mostly been fixed but if you see anything odd that does not seem intended, you should report it.

TMP: if set to 1, makes the FRME "non-sticky", which means it will only push, not pull back particles with it.